View AN1000-15_8253062.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

an1000 evaluation of the sa601/sa606 demoboard author: randall yogi 1997 aug 20 integrated circuits
philips semiconductors application note an1000 evaluation of the sa601/sa606 demoboard author: randall yogi 42 1997 aug 20 introduction philips semiconductors is dedicated to playing a major role in the wireless communication market. key to this goal is philips' commitment for design assistance at all levels. this is the purpose of the sa601/sa606 combo-board. the sa601 is a combined rf amplifier and mixer designed for high-performance low-power communication systems from 800-1200mhz. the sa606 is a low-voltage high performance monolithic fm if system that, when combined with the sa601, results in a high performance double down-conversion fm receiver. to better support this type of application, philips has combined the sa601 and sa606 ics onto a single board which highlights how well the sa601 and the sa606 work together. this application note explains how to overcome many of the technical problems that might arise, and shows how to achieve the best possible performance from the sa601 and sa606. test results are also included. this application note is divided into four main sections: i. overview of the sa601/sa606 combination board ii. layout a. schematic, components specifics and parts list b. impedance matching iii. performance a. test setup and procedures b. test data and results iv. conclusion a. q/a section i. overview both the sa601 and the sa606 are designed for portable, low voltage, low power communication applications. for a better understanding of what is involved in combining these boards, or for more information regarding the individual boards, please review application notes an1777 (for the sa601) and an1993-an1996 (for the second-if ics) which can be found in the philips rf/wireless communications data handbook, ic17. the sa601/sa606 demoboard is designed to meet amps specifications. section 2 of the eia interim standard, arecommended minimum standard for 800mhz cellular subscriber unitso (eia/is-19-b), was consulted as a guide. specific sections used were: 2.3.1 rf sensitivity 2.3.2 adjacent and alternate channel desensitization 2.3.3 intermodulation spurious-response interference 2.3.4 protection against spurious response measured results demonstrate that the sa601/sa606 demoboard successfully meets and surpasses the specifications listed above. although the sa601/sa606 demoboard is designed to meet amps cellular specifications, it can be modified for other analog cellular specifications such as tacs, etacs, and namps. the demoboard could also be configured for ism band (902mhz 928mhz) applications. ii. layout the layout of any high frequency board is critical and always challenging. as stated previously, understanding each board separately is the key to combining them. before a single-board layout was attempted, the sa601 and the sa606 individual demoboards were cascaded together, along with an rf saw filter and a 1st if saw filter. the performance with this configuration was satisfactory, thus permitting the next step of combining everything on one board (figure 2). as with the original sa601 and sa606 individual demoboards, the majority of the components are on one side of the board. the sa601/sa606 demoboard layout can be configured to provide two different types of matching to the if saw filter (figure 1). it can be configured as a 50 w impedance match, or a high impedance match to the 83.161mhz saw filter. the 50 w impedance matching network allows a designer to evaluate or troubleshoot each individual block. for example, a designer can find conversion gain measurements of the sa601 or measure sinad for only the sa606 block. sa601 matching network murata 83.161mhz saw filter matching network sa606 50 w or high impedance 50 w or high impedance sr00785 figure 1. block diagram: matching 1st if saw filter the 50 w impedance match can also be used as a reference for the high impedance match. because 50 w impedance matching requires more components, a high impedance match is preferred. matching for high impedance can be difficult, but since each block is optimized through a 50 w impedance match, the designer has a target/reference. for example, if 12db sinad = -120dbm for a 50 w impedance matched system, ideally a high impedance match should yield the same results, if not better. the majority of the single-board layout was adapted from the individual application demoboards, except for the two saw filters (the image rejection filter centered at 881mhz and the 83.161mhz saw filter). the layout for the two filters required additional design work. the 881mhz image-rejection saw filter was placed between the lna-out and the mixer-in of the sa601. placement of the 881mhz image reject saw filter, whether it was on the top or bottom of the board, did not have a dramatic impact on performance. this was because isolation between the lna-out and the mixer-in trace had already been considered in the sa601 demoboard. however, because of its high q, narrowband, and high impedance, the 83.161mhz saw filter was much more difficult to position. its placement was critical in passing amps specification 2.3.4 protection against spurious-response interference. the specification was met with margin to spare by moving the mixer-out (pins 13 and 14) of the sa601 as far away as possible from rf-in (pin 1) of the sa606. schematic, components specifics, and parts list the schematic shown in figure 3 is for both 50 w impedance matching and high impedance matching to the 83.161mhz saw filter. the schematic shows the configuration for 50 w impedance matching. by making the modifications listed in the box on the bottom right of the schematic (figure 3), the board can be configured for a high impedance match. table 1 lists the basic function of each external component for the schematic shown in figure 3. this may help answer any questions that arise about the specifics of the board.
philips semiconductors application note an1000 evaluation of the sa601/sa606 demoboard 1997 aug 20 43 sr00784 1.45o 2.15o figure 2. layout of the sa601/sa606 demoboard (not actual size)
philips semiconductors application note an1000 evaluation of the sa601/sa606 demoboard 1997 aug 20 44 1 2 3 4 5 6 7 8 9 10 20 19 18 17 16 15 14 13 12 11 vcc gnd lna in gnd gnd mixer pd gnd lo in lo in vcc gnd lna out gnd mixer in gnd mixer out mixer out gnd gnd vcc rf in c1 c3 l1 56nh c2 2.7pf 100pf c12 100pf c13 2.2pf c14 100pf l = 110 mils w = 15 mils 1 m f sa601 u1 c5 100pf ext lo (-7dbm @ 964.16 mhz) v cc c9 c4 100pf l = 470 mils w = 10 mils l = 385 mils w = 10 mils * 1 2 3 4 5 6 7 8 9 10 20 19 18 17 16 15 14 13 12 11 rf in+ rf in osc out osc in rssi aud fdbk audio rssi fdbk quad in mixer if dec if in if dec if out gnd lim in lim dec lim dec vcc lim out via top bottom w = 15 mils 881 mhz v cc c15 0.1 m f v cc 100 r1 flt1 bpfilt w = 15 mils * c10 4.7pf c11 100pf c8 33pf 2.2k r2 0.1 m f c6 18pf flt2 o sawfilt i o i c7 8.2pf l3 270nh l2 470nh l4 560nh c16 3.3pf c17 8.2pf l5 330nh c19 39pf l6 330nh c18 5-30pf c20 0.1 m f l8 1 m h c21 5-30pf l7 1.2 m h c22 1nf x1 82.705mhz c23 10pf c35 0.1 m f flt3 455khz o i c36 0.1 m f flt4 455khz o i r8 2.4k w r9 3.3k w c34 0.1 m f c33 0.1 m f c32 0.1 m f c31 10pf r1 11k w c29 390pf c30 0.1 m f l9-var 330 m h c28 open r6 open r5 0 w c27 2.2 m f r4 8.2k w c26 2.2 m f r3 10k w c25 0.1 m f c24 10 m f notes: inductors: self-resonant frequency greater than 800mhz. spiral-inductors on natural fr-4 062 mils with 1 oz. copper. this circuit is for 50 w impedance matching only. for high-z configuration these modifications need to be done: l4, l5: shorted with 0 w r2, c16, c17, c19: open replace c6 = 24pf replace c7 = 1nf replace c18 = 2.7pf replace l6 = 750nh sr00795 l = 470 mils sa606 l = 110 mils w = l = figure 3. schematic of the sa601/sa606 demoboard
philips semiconductors application note an1000 evaluation of the sa601/sa606 demoboard 1997 aug 20 45 table 1. components list: description of functionality part # description c1 lna mixer input dc blocking cap c2 part of the matching network that optimizes the return loss while minimizing the degradation of the noise figure c3 voltage compensation cap for the lna c4 lo dc blocking cap c5, c9, c14, c15, c24, c25 supply bypassing c6, c8, l3 part of the differential to single-ended translation circuit of the mixer out c7, l2 part of the matching network of the mixer output c10, c13 part of the matching network that optimizes the return loss while minimizing the degradation of the noise figure c11 mixer input dc blocking cap c12 lna output dc blocking cap c16, c17, l4, l5 part of the matching network of the 83.161mhz saw filter c18, c19, l6 part of the tapped-c network that matches the rf input of the sa606 c20 ac grounds pin 2, the rf input of the sa606 c21, c22, c23, l7, l8 colpitts oscillator network c26, c34 ac de-coupling cap c27 dc blocking cap c28, r5, r6 part of the filter network that filters 3khz-15khz on the sa7025 (low-voltage 1ghz fractional-n synthesizer). this network is only used on the 7025 ic production tester. c29, l9 quad tank component that resonates at 455khz c30 ac grounds the quad tank c31 provides the 90 phase shift to the phase detector c32, c33 if limiter decoupling cap c35, c36 if amp decoupling cap r1 dc pull-up resistor that provides isolation (reduces if to lo and rf to lo leakage) r2 sets output impedance of the mixer output r3 part of the audio op-amp that sets a gain of 2db thus stabilizing distortion r4 part of the audio op-amp that sets a gain of 2db thus stabilizing distortion r7 lowers the q of the quad tank and thus lowers the s-curve slope r8, r9 part of a network to control linearity of the rssi l1 voltage compensation to lna filt1 murata safc881.5ma70n-tc 881.5mhz bandpass saw filter: this is a 869mhz to 894mhz bandpass filter. it is used to reject the image frequency (lo + 83.16mhz in our case) and to attenuate the transmit signal (rf-45mhz) leaking through the duplexer so that the sa601 mixer doesn't reach its 1db compression point from a strong signal leaking through. some electrical characteristics from murata are provided (table 2). filt2 murata safc83.161ma51x-tc 83.161mhz saw filter: 1st-if filter for attenuating adjacent and alternate channel spurs. the filter plays a larger role in achieving the high performance of the receiver in areas such as dynamic range, spurious performance, and data communication accuracy. the 83.16mhz saw filter provides a 30khz bandpass characteristic utilizing electrodes deposited on a piezoelectric substrate. these electrodes form an inter-digitated pattern on the substrate and serve as transducers to launch an acoustic wave. when an rf voltage is applied to one set of transducers, an electric field is generated and causes the acoustic waves to propagate along the surface to an opposite transducer where an output voltage is produced. (see reference 8, alan victor). the electrical characteristics for the murata saw filter are shown in table 3. filt3, 4 murata sfgcg455bx-tc 455khz bandpass filter (30khz bandwidth). x1 an 82.705mhz crystal from either hy-q or reeves hoffman is a 3rd overtone crystal used to generate the lo for the sa606
philips semiconductors application note an1000 evaluation of the sa601/sa606 demoboard 1997 aug 20 46 table 2. electrical characteristics of the murata safc881.5ma70n-tc tested at 20 2 c. standard condition: temp = 20 2 c. humidity = 65 5%; applicable condition: temp = 5 ~ 35 c. humidity = 45 ~ 85%. item requirements typical at 20 c (reference value in standard condition) 6 1 nominal center frequency (f o ) 881.5 mhz 6 2 insertion loss i) within 869 ~ 894 mhz (pass bandwidth) ii) within dc ~ 780 mhz iii) within 824 ~ 849 mhz (duplex freq. range) iv) within 970 ~ 2000 mhz 4.5 db max. 40 db max. 20 db min. 35 db min. 3.5 db 48 db 30 db 40 db 6 3 ripple deviation (within 869 to 894 mhz) 2.0 db max. 1.0 db 6 4 v.s.w.r. (within 869 to 894 mhz) 2.5:1 max. 1.7:1 6 5 input / output impedance (nominal) 50 w // 0pf table 3. electrical characteristics of the murata safc83.161ma51x-tc item requirements 1.1 nominal center frequency (f o ) 83.161 mhz 1.2 3 db bandwidth (from 83.161 mhz) 15 khz min. 1.3 stop band attenuation (from peak level) 1.3.1 f o 1000 khz to f o 930 khz 1.3.2 f o 930 khz to f o 890 khz 1.3.3 f o 890 khz to f o 700 khz 1.3.4 f o 700 khz to f o 400 khz 1.3.5 f o 400 khz to f o 120 khz 1.3.6 f o 120 khz to f o 60 khz 1.3.7 f o + 60 khz to f o + 120 khz 1.3.8 f o + 120 khz to f o + 150 khz 1.3.9 f o + 150 khz to f o + 400 khz 1.3.10 f o + 400 khz to f o + 1000 khz 40 db min. 70 db min. 40 db min. 30 db min. 40 db min. 20 db min. 20 db min. 40 db min. 30 db min. 40 db min. 1.4 insertion loss (at minimum loss point) 5.0 db max. 1.5 ripple (within f o = 15 khz) 1.5 db max. 1.6 group delay deviation (within f o 11 khz) 10 m s max. 1.7 intermodulation input signal : f o + 60 khz, f o + 120 khz input level : 20 dbm 90 dbm max. a complete sa601/sa606 demoboard parts list is provided in table 14 at the end of this document. the parts list includes vendor names and part numbers as a convenience to designers. impedance matching matching of the 83.16mhz saw filter is an involved task. this is because the hp8753c network analyzer can only be calibrated for 50 w impedance and the 83.16mhz saw filter has a specified impedance of 850 // -2pf. refer to philips application note an1777 for an explanation of how to setup the calibration for high-impedance. although calibration at higher impedance is not as accurate as at 50 w impedance, the results were close enough to get a good impedance match. improved impedance matching yields better sensitivity performance because matching of the 83.161mhz saw filter suppresses unwanted group delay distortion. the response of the 83.161mhz saw filter is shown in figure 4. when the filter response is flat, the saw filter is matched; when it is not, group delay distortion, represented by the hump, is apparent (figure 4). center 455.0 khz res bw 3.0 vbw 3 khz span 200.0 khz #swp 1.00 sec khz ref -10.0 dbm span 200.0 khz 10.0 db at group delay distortion sr00786 figure 4. group delay distortion the steps to match the 83.161mhz saw filter to a high impedance are as follows: 1. separate the board into three sections by making two cuts in the trace. cut 1 is between the mixer out of the sa601 and the input of the saw filter. cut 2 is between the saw filter output and the rf input of the sa606. (see figure 5) sa601 murata 83.161mhz saw filter sa606 cut 1 cut 2 sr00787 mixer rf out in out in figure 5. three sections of demoboard 2. start with saw filter input of figure 6 and terminate that side with an 850 w resistor. murata 83.161mhz saw filter in out 850 w sr00788 figure 6. termination of saw filter 3. measure the impedance of the output of the saw filter by placing an sma connector on the trace and marking the corresponding impedance on the smith chart.
philips semiconductors application note an1000 evaluation of the sa601/sa606 demoboard 1997 aug 20 47 murata 83.161mhz saw filter z 1 z 2 850 w sa606 sr00789 in out rf in cut figure 7. termination matching of saw filter 4. after identifying the impedance of the saw filter output indicated by z 1 in figure 7, the rf input impedance, z 2 , must be adjusted to provide a conjugate match to z 1 . z 2 is found on the smith chart by reflecting z 1 about the purely resistive axis represented by the horizontal line running through the center of the smith chart. murata 83.161mhz saw filter sa606 matching z 1 = z 2 network sr00790 850 w in figure 8. impedance matching from saw filter to sa606 5. after a conjugate match between z 1 and z 2 has been achieved, connect the output of the saw filter to the matching network. (figure 8) murata 83.161mhz saw filter z 3 z 4 sa601 in out sr01008 sa606 cut matching z 1 = z 2 network figure 9. impedance matching from sa601 to saw filter 6. remove the 850 w resistor and measure the impedance at the saw filter input, z 3 . 7. obtain a conjugate match to z 3 at the sa601 mixer output, z 4 , and then connect together (figure 9). to double check the matching, remove the 2nd-if filter from the mixer-out of the sa606 and check the frequency response for any group delay distortion. figure 4 shows a matched saw-filter response (flat curve) and a poorly matched response that has group delay distortion. to make a quick visual check of the frequency response of the board up to the sa606 mixer output, use the fm modulation of the hp signal generator and spectrum analyzer, as follows: 1. leave the frequencies (lo and rf) at their respective values. (example: rf = 881mhz and lo = 964.16mhz) 2. set the fm deviation to 200khz and the fm modulation to 200hz on the rf's signal generator. 3. remove the 2nd-if filter connected to pin 20 of the sa606. 4. set the spectrum analyzer sweep time to 1 second, set the center frequency to the 2nd if frequency (455khz), and probe pin 20 with a fet probe. the results should look like the flat response in figure 4. iii. performance evaluation procedures the amps specification was used as a guide to test the sa601/sa606 demo board. sections 2.3.1 through 2.3.4 of the is-19-b eia interim standard were the procedures used for testing the sa601/sa606 demoboard. these tests were crucial in determining performance of the demoboard. figure 10 shows the block diagram of the test setup following the procedures outlined in the amps specification. hp8664a sig gen (rf) hp8664a sig gen (rf 30khz or 60khz) hp8664a sig gen (rf 30khz) hp8664a sig gen (lo) mini circuits combiner zfs-2-2500 mini circuits combiner zfs-2-2500 rf lo audio sa601/606 board c-message freq. devices model 581-1 philips pm3244 oscilloscope hp339 distortion meas. set mini circuits 700mhz high pass filter sr00791 with ne5532 (amplifier) figure 10. test setup for measuring rf sensitivity, adjacent and alternate channel rejection and spurious rejection transmitter desensitization occurs when the transmit signal from the handset is degrading the performance of the receiver. to measure transmitter (tx) desensitization, do the following: 1. configure the test equipment as shown in figure 11. 2. set the tx signal 45mhz below the rf signal. 3. measure the tx power at the ant of the duplexer on the hp8920a radio test set. 4. measure 12db sinad on the hp8920a radio test set when the tx signal is on and again when it is off. 5. if there is degradation in sensitivity when the tx signal is on, the difference of the 12db sinad readings is the tx desensitization. marconi 2041 signal gen mini circuits power amp zhl-1000-3w hp8664a signal gen tdk duplexer model #cf6121613 tx rx ant tektronics 2236 oscilloscope hp339 distortion meas. set hp8920a radio test set out (50w max) mini circuits 700mhz high pass filter sa601/606 board rf lo audio c-message freq. devices model 581-1 with ne5532 (amplifier) sr00792 figure 11. test setup for measuring transmitter desensitization
philips semiconductors application note an1000 evaluation of the sa601/sa606 demoboard 1997 aug 20 48 hp8664a sig gen (lo) rf lo audio sa601/606 board aprocii demoboard philips pm3244 oscilloscope hp339 distortion meas. set mini circuits 700mhz high pass filter sr01009 directional coupler mini circuits c-message freq. devices model 581-1 in out cpl hp8643a sig gen (rf) hp8643a sig gen (rf -45mhz) figure 12. test setup for measuring transmitter desensitization without duplexer because customers' preferences for duplexers vary, tx desensitization was done another way to evaluate the performance of the sa601/sa606 demoboard. 1. the setup can be configured as shown in figure 12. set rf = 869mhz, lo = 957.16mhz and tx = 824mhz. 2. set the transmit power to -10dbm because we are assuming that the tx leakage through the rx port is that much. 3. record 12db sinad. 4. reduce the transmit power by 1db and repeat step 3. 5. repeat step 4 until tx power reaches -30dbm. 6. repeat all steps for rf, lo tx frequencies at mid band (rf = 881mhz, lo = 964.16mhz, tx = 836mhz) and high band (rf = 894mhz, lo = 977.16mhz, tx = 849mhz) data and results adjacent channel, alternate channel and intermodulation spurious response the data provided in tables 4 to 6 shows the sensitivity, adjacent channel, alternate channel, and intermodulation spurious response of the demoboard. the data was taken at v cc = 3v, 4v, and 5v, as well as at three different frequencies. the data taken was recorded without a duplexer. adding a duplexer before the rf input will cause sensitivity to decrease by about 3 db. this board is well within the specified parameters for adjacent channel, alternate channel and intermodulation spurious response rejection in accordance with amps specifications. protection against spurious response interference the next set of data shown is also part of the amps specification 2.3.4 protection against spurious response interference (tables 7 to 9). the frequencies tested were the image frequencies that could cause degradation in performance. when using a tdk duplexer (tdk bandpass filter model cf6121613), the image frequencies are attenuated, so the image spurs (1047.32mhz) will not degrade the performance of the demoboard. the 2nd if image frequency is the only frequency that caused problems. this frequency is above the rf by exactly twice the 2nd if (2 455khz = 910khz). the problem occurs because, when rf + 910khz mixes with the 1st lo (964.16mhz), the frequency produced is (rf + 910khz 1st lo = 82.25mhz). this is equal to the 2nd if image frequency. when the 2nd if image frequency is mixed with the crystal oscillator, the frequency produced is the 2nd-if frequency. the sa606 will demodulate this unwanted frequency, as well as the desired signal. example: rf = 881mhz lo = 964.16mhz 2nd lo = 82.705mhz 881mhz + 910khz = 881.91mhz 881.910mhz mixes with the lo (964.16mhz) = 82.25mhz 82.25mhz mixes with the 2nd lo (82.705mhz) = 455khz to resolve this problem, the 83.161mhz saw filter must be isolated. the unwanted frequency was leaking around the saw filter and into the rf input of the sa606. so the distance between the sa601 mixer out to the rf input of the sa606 was increased by rotating the saw filter. this solved the problem and the board met the protection against spurious response specification with at least 14db to spare. transmitter desensitization another issue was to evaluate how the sa601/sa606 performs with the transmit section of a radio on (transmitter desensitization). transmitter desensitization will degrade the sensitivity of the receiver if the strong tx signal is allowed to pass through and cause the sa601 to reach its 1db compression point in the lna and the mixer. tables 10 to 12 show the results of three test boards for transmitter desensitization as the transmit power is increased from 100mw to 1w. using a tdk duplexer (tdk bandpass filter model cf6121613), the board performed well. at most, the board degraded by 2db from the transmitter desensitization. since most customers will not want to use the tdk duplexer, tx desensitization was done another way, as explained in the procedures. table 13 show the results. the results show that with a duplexer that has tx leakage of -14dbm or less through the rx port, the sa601/sa606 will meet the sensitivity requirement according to is-19-b (-116dbm for 12 db sinad), assuming the duplexer has 3db of loss. rssi, am rejection, thd, noise, audio output level the next set of data shows rssi performance at 3v, 4v, and 5v (figure 13) and am rejection, thd, noise, and audio output level (figure 14). voltage (v) rf input level (dbm) 2.50 2.00 1.50 1.00 0.50 0.00 -130 -125 -120 -115 -110 -105 -100 -95 -90 -85 -80 -75 -70 -65 -60 -55 -50 -45 -40 -35 -30 -25 -20 = 5v = 4v = 3v sr00793 figure 13. rssi (average of three boards)
philips semiconductors application note an1000 evaluation of the sa601/sa606 demoboard 1997 aug 20 49 10.00 relative to audio output (db) rf input level (dbm) 0.00 -10.00 -20.00 -30.00 -40.00 -50.00 -60.00 -70.00 audio output level thd am rejection noise sr00794 -130 -125 -120 -115 -110 -105 -100 -95 -90 -85 -80 -75 -70 -65 -60 -55 -50 -45 -40 -35 -30 -25 -20 figure 14. receiver performance (average of three boards) iv. conclusion the sa601/sa606 application demoboard demonstrates how well the two chips perform together. meeting the stated amps cellular specifications is a good test of a receiver's performance. not all receivers can meet these stringent requirements. the sa601/sa606 demoboard not only meets, but exceeds, the criteria of sensitivity with 12db sinad of about -122dbm, which is 3db better than amps specification, assuming 3db loss from the duplexer. adjacent channel exceeds the requirement by 33db, alternate channel exceeds the requirement by 7.5db, intermodulation spurious response exceeds the requirement by 4.5db, and protection against spurious response interference exceeds the requirement by 11db. many key factors such as board layout and impedance matching help the performance exceed the receiver specifications for amps. many issues looked at in this application note will help answer customers' questions as philips customers design greater and better things. questions and answers q. what is the difference between the 50 w demoboard and the high-impedance demoboard? a. visually, the 50 w boards have more components near the 83.161mhz saw filter. the 50 w boards have two 5-30pf trim capacitors. the high-impedance board out performs the 50 w board by 1db on sensitivity. keep in mind that the 50 w board allows troubleshooting of each block. q. what do i do if i don't achieve the sensitivity as the data shows? a. here is a check list you can follow: 1. check the solder connections. 2. make sure the lo drive level is -5dbm to -7dbm to the sa601 mixer. 3. check for the 700mhz high pass filter (see figure 10). 4. check the c-message filter. (an active c-message filter with 10db of gain was used for sensitivity tests.) 5. probe for signals from the sa601 inputs down to the sa606 limiter-out. check to see if there are significant losses. the probe points are: a. rf input of the sa601 b. lo input of the sa601 c. lna-out of the sa601 d. before the 881mhz saw filter e. after the 881mhz saw filter f. mixer-in of the sa601 g. mixer-out of the sa601 h. before the 83.161mhz saw filter i. after the 83.161mhz saw filter j. rf input of the sa606 k. the 82.705mhz crystal l. mixer-out of the sa606 m. if-in of the sa606 n. if-out of the sa606 o. limiter-in of the sa606 p. limiter-out of the sa606 q. what is the difference between the 1008hs and the 1008cs inductors from coilcraft? a. there is no difference in performance between the two types of inductors. the only external difference is the packaging. q. what should i do if i don't meet the specification for protection against spurious-response? a. make sure that all the grounds of the 83.161mhz saw filter are connected, especially the grounds closest to the input and output. shield each section which will isolate each block and improve performance. q. why do you use an if of 83.16mhz instead of 45mhz? a. 83.16mhz is used as the if because, at 45mhz, serious problems may result because of the existence of spurious performance degradation and potential interference due to the half-if mixer spurious content. the half-if (rf + 22.5mhz) is only a problem with if frequencies which are less than twice the receiver bandwidth. an amps receiver with 45mhz 1st if can have a half-if problem, while at 83.16mhz it will not because the half-if, at 45mhz for example, will be 891.50mhz (869mhz + 22.5mhz). since 891.5mhz falls in the pass band, this signal will desensitize the receiver. also, at 83.16mhz, the image frequency is further away than 45mhz. (see reference 8) q. will phase noise of the signal generator cause performance degradation when testing tx desensitization? a. yes it will because, when doing the tx desensitization test without a duplexer, sensitivity dramatically improved as levels on the signal generator were decremented. also, when cascading two duplexers together, the noise was attenuated and sensitivity improved. in most handsets, a bandpass filter (center frequency at 836mhz) is placed before the power amplifier; therefore, the out-of-band noise is attenuated before being amplified. this attenuation will lower the phase noise and allow less tx desensitization. q. what spurs will effect the sensitivity of the receiver? how can these spurs be rejected? a. consult table below for unwanted spurs: spurs eq. 1 range (mhz) rejected by... 1st image rf+2(if1) 1035.321060.32 duplexer 2nd image rf+2(if2) 869.91894.91 83.16mhz saw half if rf+.5(if1) 910.58935.58 duplexer tx intermod 2 tx45mhz 779804 duplexer tx isolation 2 tx + if1 907.16932.16 duplexer notes: 1. if1 = 83.16mhz; if2 = 455khz 2. not measured
philips semiconductors application note an1000 evaluation of the sa601/sa606 demoboard 1997 aug 20 410 v. references 1. aan1777: low voltage front-end circuitso, rf/wireless communications, data handbook, philips semiconductors, 1995. 2. aan1993: high sensitivity application of low-power rf/if integrated circuitso, rf/wireless communications, data handbook, philips semiconductors, 1995. 3. aan1994: reviewing key areas when designing with the sa605o, rf/wireless communications, data handbook, philips semiconductors, 1995. 4. aan1995: evaluating the sa605 so and ssop demoboard, rf/wireless communications, data handbook, philips semiconductors, 1995. 5. aan1996: demodulation at 10.7mhz if with sa605/625o, rf/wireless communications, data handbook, philips semiconductors, 1995. 6. alow-voltage lna and mixer - 1ghzo, (sa601 data sheet), rf/wireless communications, data handbook, philips semiconductors, 1995. 7. alow-voltage high performance mixer fm if systemo, (sa606 data sheet), rf/wireless communications, data handbook, philips semiconductors, 1995. 8. victor, alan, asaw filters aid communications system performanceo, microwaves and rf, aug. 1991, pg. 104-111. 9. arecommended minimum standards for 800-mhz cellular subscriber unitso, eia/is-19-b. electronic industries association, 1988. table 4. rf sensitivity, adjacent and alternate channel rejection, and intermodulation spurious response rejection at v cc = 3v all data taken without a duplexer. frequency 12 db sinad adjacent channel above (+30khz) adjacent channel below (-30khz) alternate channel above (+60khz) alternate channel below (-60khz) intermodulation spurious response (+60 & +120 khz) intermodulation spurious response (-60 & -120 khz) high impedance board #1: adjacent and alternate channel; fm dev = 8khz, fm mod = 400hz rf = 881mhz; lo = 964.161mhz -122 dbm 55 db 53 db 86 db 88 db 71.5 db 70.5 db rf = 869mhz; lo = 952.161mhz -122 dbm 49 db 50 db 88 db 87 db 70.5 db 70.5 db rf = 894mhz; lo = 977.161mhz -122 dbm 51 db 54 db 88 db 87 db 71.5 db 70 db high impedance board #2: adjacent and alternate channel; fm dev = 8khz, fm mod = 400hz rf = 881mhz; lo = 964.161mhz -122.5 dbm 51.5 db 52.5 db 71.5 db 77.5 db 71 db 71 db rf = 869mhz; lo = 952.161mhz -123 dbm 52 db 51 db 72 db 82 db 70.5 db 70.5 db rf = 894mhz; lo = 977.161mhz -122.5 dbm 51.5 db 50.5 db 72.5 db 77.5 db 69.5 db 69.5 db high impedance board #3: adjacent and alternate channel; fm dev = 8khz, fm mod = 400hz rf = 881mhz; lo = 964.161mhz -122 dbm 49 db 54 db 91 db 87 db 73 db 71 db rf = 869mhz; lo = 952.161mhz -123 dbm 50 db 56 db 93 db 88 db 73 db 71 db rf = 894mhz; lo = 977.161mhz -122 dbm 50 db 55 db 92 db 89 db 72 db 71 db requirements per is-19-b: 2.3.1 rf sensitivity: -116dbm or better 2.3.2 adjacent and alternate channel desensitization: 16dbm min for adjacent channel; 60db min for alternate channel. 2.3.3 intermodulation spurious response interference: 65db min.
philips semiconductors application note an1000 evaluation of the sa601/sa606 demoboard 1997 aug 20 411 table 5. rf sensitivity, adjacent and alternate channel rejection, and intermodulation spurious response rejection at v cc = 4v all data taken without a duplexer. frequency 12 db sinad adjacent channel above (+30khz) adjacent channel below (-30khz) alternate channel above (+60khz) alternate channel below (-60khz) intermodulation spurious response (+60 & +120 khz) intermodulation spurious response (-60 & -120 khz) high impedance board #1: adjacent and alternate channel; fm dev = 8khz, fm mod = 400hz rf = 881mhz; lo = 964.161mhz -122 dbm 51 db 52 db 88 db 86 db 71.5 db 69.5 db rf = 869mhz; lo = 952.161mhz -122 dbm 50 db 51 db 88 db 87 db 72.5 db 69.5 db rf = 894mhz; lo = 977.161mhz -122 dbm 51 db 51 db 87 db 87 db 72 db 70 db high impedance board #2: adjacent and alternate channel; fm dev = 8khz, fm mod = 400hz rf = 881mhz; lo = 964.161mhz -122.5 dbm 51.5 db 51.5 db 70.5 db 67.5 db 70.5 db 69.5 db rf = 869mhz; lo = 952.161mhz -122.5 dbm 52.5 db 50.5 db 71.5 db 80.5 db 69 db 69 db rf = 894mhz; lo = 977.161mhz -122 dbm 52 db 51 db 72 db 76 db 70 db 76 db high impedance board #3: adjacent and alternate channel; fm dev = 8khz, fm mod = 400hz rf = 881mhz; lo = 964.161mhz -122 dbm 50 db 55 db 91 db 87 db 73 db 71 db rf = 869mhz; lo = 952.161mhz -123 dbm 50 db 54 db 93 db 88 db 73 db 70 db rf = 894mhz; lo = 977.161mhz -123 dbm 50 db 53 db 91 db 87 db 72 db 70 db requirements per is-19-b: 2.3.1 rf sensitivity: -116dbm or better 2.3.2 adjacent and alternate channel desensitization: 16dbm min for adjacent channel; 60db min for alternate channel. 2.3.3 intermodulation spurious response interference: 65db min. table 6. rf sensitivity, adjacent and alternate channel rejection, and intermodulation spurious response rejection at v cc = 5v. all data taken without a duplexer. frequency 12 db sinad adjacent channel above (+30khz) adjacent channel below (-30khz) alternate channel above (+60khz) alternate channel below (-60khz) intermodulation spurious response (+60 & +120 khz) intermodulation spurious response (-60 & -120 khz) high impedance board #1: adjacent and alternate channel; fm dev = 8khz, fm mod = 400hz rf = 881mhz; lo = 964.161mhz -122 dbm 50 db 52 db 86 db 85 db 71.5 db 69.5 db rf = 869mhz; lo = 952.161mhz -122 dbm 49 db 52 db 87 db 86 db 71.5 db 69 db rf = 894mhz; lo = 977.161mhz -122 dbm 52 db 51 db 86 db 86 db 72 db 70 db high impedance board #2: adjacent and alternate channel; fm dev = 8khz, fm mod = 400hz rf = 881mhz; lo = 964.161mhz -122 dbm 52 db 50 db 70 db 76 db 70.5 db 69.5 db rf = 869mhz; lo = 952.161mhz -122.5 dbm 52.5 db 49.5 db 70.5 db 78.5 db 69 db 69 db rf = 894mhz; lo = 977.161mhz -121.5 dbm 52.5 db 50.5 db 71.5 db 75.5 db 70 db 68 db high impedance board #3: adjacent and alternate channel; fm dev = 8khz, fm mod = 400hz rf = 881mhz; lo = 964.161mhz -121.5 dbm 49.5 db 53.5 db 90.5 db 86.5 db 73 db 70 db rf = 869mhz; lo = 952.161mhz -122.5 dbm 52.5 db 49.5 db 87.5 db 91.5 db 73 db 70 db rf = 894mhz; lo = 977.161mhz -121 dbm 50 db 53 db 91 db 87 db 72 db 70 db requirements per is-19-b: 2.3.1 rf sensitivity: -116dbm or better 2.3.2 adjacent and alternate channel desensitization: 16dbm min for adjacent channel; 60db min for alternate channel. 2.3.3 intermodulation spurious response interference: 65db min.
philips semiconductors application note an1000 evaluation of the sa601/sa606 demoboard 1997 aug 20 412 table 7. protection against spurious response interference v cc = 3v all test measured with tdk duplexer (model cf6121613d) frequency interfering frequency (mhz) board #1 board #2 board #3 -121 dbm for 12 db sinad -121 dbm for 12 db sinad -121 dbm for 12 db sinad rf 881mh 881.91 82.5 db 76.5 db 78.5 db rf = 881mhz; lo = 964 161mhz 922.58 108.5 db 108.5 db 108.5 db lo = 964 . 161mhz 1005.74 108.5 db 108.5 db 108.5 db 1047.32 99.5 db 97.5 db 92.5 db -119.5 dbm for 12 db sinad -121 dbm for 12 db sinad -120 dbm for 12 db sinad rf 869mh 869.91 81 db 73.5 db 75.5 db rf = 869mhz; lo = 952 161mhz 910.58 108 db 108.5 db 107.5 db lo = 952 . 161mhz 993.74 108 db 108.5 db 107.5 db 1035.32 98 db 95.5 db 88.5 db -119 dbm for 12 db sinad -120 dbm for 12 db sinad -119.5 dbm for 12 db sinad rf 894mhz; 894.91 79.5 db 82.5 db 79 db rf = 894mh z; lo = 977.161mhz 935.58 108.5 db 110.5 db 108 db lo = 977 . 161mhz 1018.74 108.5 db 110.5 db 108 db 1060.32 99.5 db 100.5 db 96 db requirements per is-19-b: 2.3.4 protection against spurious response interference: 60db min. table 8. protection against spurious response interference v cc = 4v all test measured with tdk duplexer (model cf6121613d) frequency interfering frequency (mhz) board #1 board #2 board #3 -121 dbm for 12 db sinad -121 dbm for 12 db sinad -121.5 dbm for 12 db sinad rf 881mh 881.91 84.5 db 74.5 db 79 db rf = 881mhz; lo = 964 161mhz 922.58 108.5 db 108.5 db 109 db lo = 964 . 161mhz 1005.74 108.5 db 108.5 db 109 db 1047.32 101.5 db 98.5 db 93 db -120 dbm for 12 db sinad -120.5 dbm for 12 db sinad -120 dbm for 12 db sinad rf 869mh 869.91 80.5 db 71 db 73.5 db rf = 869mhz; lo = 952 161mhz 910.58 107.5 db 108 db 107.5 db lo = 952 . 161mhz 993.74 107.5 db 108 db 107.5 db 1035.32 95.5 db 93 db 88.5 db -119.5 dbm for 12 db sinad -120 dbm for 12 db sinad -120 dbm for 12 db sinad rf 894mhz; 894.91 80 db 78.5 db 81.5 db rf = 894mh z; lo = 977.161mhz 935.58 108 db 108.5 db 107.5 db lo = 977 . 161mhz 1018.74 108 db 108.5 db 107.5 db 1060.32 100 db 99.5 db 95.5 db requirements per is-19-b: 2.3.4 protection against spurious response interference: 60db min.
philips semiconductors application note an1000 evaluation of the sa601/sa606 demoboard 1997 aug 20 413 table 9. protection against spurious response interference v cc = 5v all test measured with tdk duplexer (model cf6121613d) frequency interfering frequency (mhz) board #1 board #2 board #3 -121 dbm for 12 db sinad -121 dbm for 12 db sinad -121.5 dbm for 12 db sinad rf 881mh 881.91 84.5 db 74 db 77.5 db rf = 881mhz; lo = 964 161mhz 922.58 108.5 db 109 db 108.5 db lo = 964 . 161mhz 1005.74 108.5 db 109 db 108.5 db 1047.32 108.5 db 97 db 104.5 db -120 dbm for 12 db sinad -120.5 dbm for 12 db sinad -120 dbm for 12 db sinad rf 869mh 869.91 79.5 db 71 db 71 db rf = 869mhz; lo = 952 161mhz 910.58 107.5 db 108 db 108 db lo = 952 . 161mhz 993.74 107.5 db 108 db 108 db 1035.32 101.5 db 94 db 93 db -119.5 dbm for 12 db sinad -120 dbm for 12 db sinad -120 dbm for 12 db sinad rf 894mhz; 894.91 80.5 db 77 db 81.5 db rf = 894mh z; lo = 977.161mhz 935.58 107.5 db 108 db 111.5 db lo = 977 . 161mhz 1018.74 107.5 db 108 db 111.5 db 1060.32 106.5 db 100 db 106.5 db requirements per is-19-b: 2.3.4 protection against spurious response interference: 60db min.
philips semiconductors application note an1000 evaluation of the sa601/sa606 demoboard 1997 aug 20 414 table 10. transmit desensitization board #1 frequency transmit power (mw) 12 db sinad without tx (dbm) 12 db sinad with tx (dbm) tx desensitization (db) 100 -120 -119.5 0.5 200 -120 -119.5 0.5 300 -120 -119 1 rf = 881mhz ; 400 -120 -119 1 rf = 881mhz lo = 964.161mhz, t 836mh 500 -120 -119 1 tx = 836mhz 600 -120 -119 1 700 -120 -119 1 800 -120 -118 2 900 -120 -118 2 1000 -120 -118 2 100 -119.5 -119.5 0 200 -119.5 -119.5 0 300 -119.5 -119.5 0 rf = 869mhz ; 400 -119.5 -119.5 0 rf = 869mhz lo = 952.161mhz, t 824mh 500 -119.5 -119.5 0 tx = 824mhz 600 -119.5 -119.5 0 700 -119.5 -119.5 0 800 -119.5 -119.5 0 900 -119.5 -119.5 0 1000 -119.5 -119.5 0 100 -119 -119 0 200 -119 -119 0 300 -119 -119 0 rf = 894mhz; 400 -119 -119 0 rf 894mhz lo = 977.161mhz, t 849mh 500 -119 -119 0 t x = 849mh z 600 -119 -119 0 700 -119 -119 0 800 -119 -119 0 900 -119 -119 0 1000 -119 -119 0 requirements per is-19-b: 2.3.1 rf sensitivity: -116dbm or better
philips semiconductors application note an1000 evaluation of the sa601/sa606 demoboard 1997 aug 20 415 table 11. transmit desensitization board #2 frequency transmit power (mw) 12 db sinad without tx (dbm) 12 db sinad with tx (dbm) tx desensitization (db) 100 -120 -119.5 0.5 200 -120 -119.5 0.5 300 -120 -119 1 rf = 881mhz ; 400 -120 -119 1 rf = 881mhz lo = 964.161mhz, t 836mh 500 -120 -119 1 tx = 836mhz 600 -120 -119 1 700 -120 -119 1 800 -120 -118 2 900 -120 -118 2 1000 -120 -118 2 100 -119.5 -119.5 0 200 -119.5 -119.5 0 300 -119.5 -119.5 0 rf = 869mhz ; 400 -119.5 -119.5 0 rf = 869mhz lo = 952.161mhz, t 824mh 500 -119.5 -119.5 0 tx = 824mhz 600 -119.5 -119.5 0 700 -119.5 -119.5 0 800 -119.5 -119.5 0 900 -119.5 -119.5 0 1000 -119.5 -119.5 0 100 -119.5 -119.5 0 200 -119.5 -119.5 0 300 -119.5 -119.5 0 rf = 894mhz; 400 -119.5 -119.5 0 rf 894mhz lo = 977.161mhz, t 849mh 500 -119.5 -119.5 0 t x = 849mh z 600 -119.5 -119 0.5 700 -119.5 -119 0.5 800 -119.5 -119 0.5 900 -119.5 -119 0.5 1000 -119.5 -119 0.5 requirements per is-19-b: 2.3.1 rf sensitivity: -116dbm or better
philips semiconductors application note an1000 evaluation of the sa601/sa606 demoboard 1997 aug 20 416 table 12. transmit desensitization board #3 frequency transmit power (mw) 12 db sinad without tx (dbm) 12 db sinad with tx (dbm) tx desensitization (db) 100 -119.8 -119.3 0.5 200 -119.8 -119.3 0.5 300 -119.8 -118.8 1 rf = 881mhz ; 400 -119.8 -118.8 1 rf = 881mhz lo = 964.161mhz, t 836mh 500 -119.8 -118.8 1 tx = 836mhz 600 -119.8 -118.8 1 700 -119.8 -118.8 1 800 -119.8 -117.8 2 900 -119.8 -117.8 2 1000 -119.8 -117.8 2 100 -119 -117 0 200 -119 -117 0 300 -119 -117 0 rf = 869mhz ; 400 -119 -117 0 rf = 869mhz lo = 952.161mhz, t 824mh 500 -119 -117 0 tx = 824mhz 600 -119 -117 0 700 -119 -117 0 800 -119 -117 0 900 -119 -117 0 1000 -119 -117 0 100 -119 -119 0 200 -119 -119 0 300 -119 -119 0 rf = 894mhz; 400 -119 -119 0 rf 894mhz lo = 977.161mhz, t 849mh 500 -119 -119 0 t x = 849mh z 600 -119 -118.5 0.5 700 -119 -118.5 0.5 800 -119 -118.5 0.5 900 -119 -118.5 0.5 1000 -119 -118.5 0.5 requirements per is-19-b: 2.3.1 rf sensitivity: -116dbm or better
philips semiconductors application note an1000 evaluation of the sa601/sa606 demoboard 1997 aug 20 417 table 13. transmit desensitization without duplexer tl l board #1 board #2 board #3 tx level (dbm) 12db sinad (dbm) 12db sinad (dbm) 12db sinad (dbm) (dbm) 824mhz 836mhz 849mhz 824mhz 836mhz 849mhz 824mhz 836mhz 849mhz -10 -118.5 -117.5 -117 -119 -118.5 -117.5 -119 -118.5 -117.5 -11 -118.5 -118 -117 -119 -118.5 -117.5 -119 -118.5 -117.5 -12 -118.5 -118 -117 -119.5 -118.5 -118 -119.5 -119 -117.5 -13 -119 -118.5 -117.5 -119.5 -119 -118 -119.5 -119 -118 -14 -120 -119.5 -119 -120.5 -120 -119.5 -121 -120.5 -119 -15 -120 -120 -119 -121 -120.5 -119.5 -121 -120.5 -119.5 -16 -120.5 -120 -119.5 -121 -120.5 -120 -121 -121 -120 -17 -120.5 -120 -119.5 -121 -121 -120.5 -121 -121 -120 -18 -120.5 -120.5 -120 -121 -121 -120.5 -121.5 -121 -120.5 -19 -121 -121 -120.5 -122 -121.5 -121.5 -122 -122 -121 -20 -121.5 -121 -121 -122 -122 -121.5 -122 -122 -121.5 -21 -121.5 -121 -121 -122 -122 -121.5 -122.5 -122 -121.5 -22 -121.5 -121.5 -121 -122 -122 -122 -122.5 -122.5 -121.5 -23 -121.5 -121.5 -121.5 -122.5 -122 -122 -122.5 -122.5 -121.5 -24 -122 -122 -121.5 -122.5 -122.5 -122 -122.5 -122.5 -121.5 -25 -122 -122 -121.5 -122.5 -122.5 -122.5 -123 -123 -121.5 -26 -122 -122 -121.5 -122.5 -122.5 -122.5 -123 -123 -122 -27 -122 -122 -122 -123 -122.5 -122.5 -123 -123 -122 -28 -122 -122 -122 -123 -122.5 -122.5 -123 -123 -122 -29 -122.5 -122 -122 -123 -123 -122.5 -123 -123 -122.5 -30 -122.5 -122 -122 -123 -123 -122.5 -123 -123 -122.5 off -122.5 -122 -122 -123 -123 -122.5 -123 -123 -122.5 requirements per is-19-b: 2.3.1 rf sensitivity: -116dbm or better
philips semiconductors application note an1000 evaluation of the sa601/sa606 demoboard 1997 aug 20 418 table 14. customer application component list for sa601/sa606 qty. part value part reference part description vendor mfg part number **** surface mount capacitors **** 1 2.2pf c13 npo ceramic 0805 .25pf garrett philips 0805cg229c9bb0 1 2.7pf c2 npo ceramic 0805 .25pf garrett philips 0805cg279c9bb0 1 2.7pf c18 for hi z board npo ceramic 1206 .25pf garrett rohm 1206mch315a2r7ck 1 3.3pf c16 npo ceramic 0805 .25pf garrett philips 0805cg339c9bb0 1 4.7pf c10 npo ceramic 0805 .25pf garrett philips 0805cg479c9bb0 2 8.2pf c7, c17 npo ceramic 0805 5pf garrett philips 0805cg829c9bb0 2 10pf c23, c31 npo ceramic 0805 5% garrett philips 0805cg100j9bb0 1 18pf c6 npo ceramic 0805 5% garrett philips 0805cg180j9bb0 1 24pf c6 for hi z board npo ceramic 0805 5% garrett philips 0805cg240j9bb0 1 33pf c8 npo ceramic 0805 5% garrett philips 0805cg330j9bb0 1 39pf c19 npo ceramic 0805 5% garrett philips 0805cg390j9bb0 6 100pf c1, c4, c5, c11, c12, c14 npo ceramic 0805 5% garrett philips 0805cg101j9bb0 1 390pf c29 npo ceramic 0805 5% garrett philips 0805cg391j9bb0 2 1nf c22, (c7 for hi z board) npo ceramic 0805 5% garrett philips 0805cg102j9bb0 10 100nf c9, c15, c20, c25, c30, c32, c33, c34, c35, c36 z5u ceramic 0805 20% garrett philips 08052e104m9bb0 1 1 m f c3 tant chip cap 10% garrett philips 49mc105a016koas 2 2.2 m f c26, c27 tant chip cap 10% garrett philips 49mc225a010koas 1 10 m f c24 tant chip cap 10% garrett koa speer tmc-m1ab106klrh 2 5-30pf c18, c21 smt trimmer cap jaco kyocera ctz3s-30c-b **** resistors **** 1 0 w r5 res. chip 0805 1/10w 5% garrett koa speer rm73b2a-f000 1 100 w r1 res. chip 0805 1/10w 5% garrett koa speer rm73b2a-f101 1 2.2k w r2 res. chip 0805 1/10w 5% garrett koa speer rm73b2a-f222 1 2.4k w r8 res. chip 0805 1/10w 5% garrett koa speer rm73b2a-f242 1 3.3k w r9 res. chip 0805 1/10w 5% garrett koa speer rm73b2a-f332 1 8.2k w r4 res. chip 0805 1/10w 5% garrett koa speer rm73b2a-f822 1 10k w r3 res. chip 0805 1/10w 5% garrett koa speer rm73b2a-f103 1 11k w r7 res. chip 0805 1/10w 5% garrett koa speer rm73b2a-f113 **** inductors **** 1 56nh l1 chip inductor 10% coilcraft coilcraft 1008cs-560 10% 1 270nh l3 chip inductor 10% coilcraft coilcraft 1008cs-271 10% 2 330nh l5, l6 chip inductor 10% coilcraft coilcraft 1008cs-331 10% 1 470nh l2 chip inductor 10% coilcraft coilcraft 1008cs-471 10% 1 560nh l4 chip inductor 10% coilcraft coilcraft 1008cs-561 10% 1 750nh l6 hi z board chip inductor 10% coilcraft coilcraft 1008cs-751 10% 1 1.2 m h l7 chip inductor 10% coilcraft coilcraft 1008cs-122 10% 1 330 m h l9 variable smt inductor digikey toko tks2272ct-nd 3% 1 1 m h l8 chip inductor 10% coilcraft coilcraft 1008cs-102 10% **** filters **** 1 881.5mhz filt1 881.5mhz saw bandpass murata murata safc881.5ma70n-tc 1 83.161mhz filt2 83.161mhz saw bandpass murata murata safc83.161ma51x-tc 2 455khz filt3, filt4 455khz fm if filter murata murata sfgcg455bx-tc **** ic **** 1 sa601 u1 low voltage lna & mixer philips philips sa601dk 1 sa606 u2 low voltage fm if system philips philips sa606dk **** miscellaneous **** 1 82.705mhz x1 82.705mhz crystal hy-q international or reeveshoffman 82.705mhz 2 sma gold connector digikey j502-nd ef johnson 142-0701-801 1 5 pins gold test point digikey 3m929647-01-36-nd 1 printed circuit board rf# 30042 excel 601/606 #30042

▲Up To Search▲

Price & Availability of AN1000-15

	To Download AN1000-15 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .